delabs Circuits

Showing posts with label Oscillators. Show all posts
Showing posts with label Oscillators. Show all posts

Friday, February 10, 2017

Function Generator using ICL8038

ICL8038 and XR-2206 can help you build a Function Generator or Wavform Generator. It is needed along with the Oscilloscope and Power Supply on the Workbench.

The ICL8038 waveform generator is a monolithic integrated circuit capable of producing high accuracy sine, square, triangular, sawtooth and pulse waveforms with a minimum of external components. The frequency (or repetition rate) can be selected externally from 0.001Hz to more than 300kHz using either resistors or capacitors, and frequency modulation and sweeping can be accomplished with an external voltage.

See the Full page with parts list at my Website - Function Generator using ICL8038.

Function Generator using ICL8038

Specifications

Frequency range - 0.95 Hz to 105 KHz in five decade ranges
Waveforms - Sine, Triangular and Square.
Output amplitude - Adjustable from 10 mV PP. to 10 V PP
Output impedance - 50 ohms.

Thursday, February 09, 2017

VCO - Voltage Controlled Oscillator using Opamps

This is a Voltage to pulse converter using opamps for measuring speed or rate from a Tacho Motor mechanical coupled to a Conveyor System.

See the complete circuit in my site to study other sections. The motor DC out is filtered and scaled. Then the clean safe dc is fed to this VCO based on a generic application note design. 

The pulses can be used to advance digital counter or mechanical counter using a solenoid driver transistor circuit. The Voltage Vin can be further scaled and fed to a Digital Panel meter to read the rate.

VCO - Voltage Controlled Oscillator using Opamps


VCO - Voltage Controlled Oscillator using Opamps. LM339 is a quad  Comparator.

The complete PDF circuit and other such circuits at my Mixed Circuits Analog with Digital

Sunday, March 20, 2016

Square and Triangle Opamp Oscillator

Here is the circuit of a Op-Amp based Square Wave Generator. One of the main application of this is in a Simple PWM circuit and Triangle Opamp Oscillator. The Slope of the Triangle wave is compared with a DC Level to derive a pulse width or On-Time proportional to a Voltage.

Tutorials on Basics and Instrumentation Electronics

This On-Time proportional to voltage is for a fixed oscillation rate based on C2-C3 and R15. The C2-C3 form a Unpolarized cap, This type is also used in crossover networks in speaker boxes. This is because, a plastic 4.7 uF (2 * 10uF series) is big and costlier, but a plastic cap is very stable and closer to an ideal cap.

Square and Triangle Opamp Oscillator

First you need to know that most opamps in such circuits can give a square wave, but very few can swing to the rails (+/-5). For designing take 75% of Vcc. CA3130 is one that can swing to rails like a CMOS gate.

Assuming the swing of output is around +/- 4V, the pin 10 + input will be at +/- 2V. When the cap is discharged at 0 V, let us take that the output is +, the cap charges to a little above +2, - input becomes dominant, so output swings negative. This discharges the cap to 0 and then charges it negatively upto -2. This in turn flips the output to + as pin 10 turns dominant. Hence this continues as a oscillation, with a nice triangle across the cap for the PWM comparator.

Dominant means more +, 0 is positive compared to -2V. Also -2.5 is negative compared to -2.2.

Related Reading - Op Amp Triangle-Wave Generator

Thursday, October 08, 2015

PLL using 4046 - Phase Locked loop

CD4046 is a PLL or phase lock loop, it mainly consists of a VCO and phase comparators. This is a component in FM demodulation and modulation.

Mixed and Interface Circuits

PLL using 4046

It is used in a closed loop control to maintain a stable frequency. The Circuit above is good for learning the full use of a small Dual Trace Scope. The Circuit has both Analog and Digital areas and is a part of communication.
Read the pages above for building more Knowledge on PLL

Monday, September 07, 2015

VCO with LM331

This Circuit is a simple Analog to Digital Interface with a capability of 10 to 12 bits resolution. 10 bits means 1024 counts or parts of a full scale FS which is close to 3-1/2 1999 counts.
VCO with LM331

In this 1 V can be read as 1.000 V that means even 1mV can be resolved for FS of 1V.
The Caps C6 and others must be plastic multilayer low-leakage types for accuracy of reading.
Use all 1% MFR 100ppm or better resistors, Design gain of U1B for the Full Scale you want.

The Output Fout is a Frequency which is directly proportional to the measured voltage Vin.
The pulses can be isolated using opto-couplers to avoid ground loops or electric hazard.
An additional protection and scaling circuit at the input may be required for some sensors.

Tuesday, June 09, 2015

LM311 Square Triangle Oscillator for PWM

LM311 is a comparator, It operates from single 5V supply or dual supplies,input current 150 nA, 50 V-50 mA output drive capability. TTL-CMOS compatible output.

Even LM324  used as a  comparator Water Level Indicator with Reed Relays

The Output is open collector so it can sink current but cannot source, a totem pole output can source and sink. In this Circuit R2 is the source or pull-up.

LM311 Square Triangle Oscillator for PWM

The Output being high or low depends on which input is more dominant or positive. If + or non-inverting input is more positive than the - inverting input then output of LM311 is high impedance or high Z as output transistor of LM311 is turned off, but output goes high due to R2 pull-up 1K, so you can apply a load of 10K and above for source. When the - input or inverting input is more positive, output goes Low as transistor turns on, now a current of upto 50mA can sink here, a LED or Relay can be driven.

Mixed Circuits Analog with Digital

On turn on C2 capacitor is discharged and pin 3 the inverting input is at a lower potential than pin 2 the non-inverting which is at 2.5V. Hence output goes high and C2 starts charging thru R5, When C2 charges a little beyond 2.5V pin 3 is more dominant and output goes low now, this slowly discharges the C2 bringing the voltage at pin 3 again below 2.5V so output goes high again. This process goes on, hence it oscillates. The charging and discharging is at the rate of R5 * C2 approx. , R3 serves as hysteresis or feedback to ensure clean turn on and off.

Monday, May 11, 2015

Crystal Oscillator - Parallel Resonant

74HCU04 is a chip that was made for this purpose, HCT may not work for such a circuit. C1 and C2 can go to upto 33pF and R2 can be increased to make R2 * C2 = t.

Time constant much less than the period T of the crystal T = 1/F . This is to remove higher frequency components in the Oscillator.

More on Piezoelectric Crystal Oscillator
Crystal Oscillator - Parallel Resonant

The circuit above is a parallel resonant oscillator circuit. The Crystal works by the piezoelectric principle, piezo means pressure. The electric field causes the impedance of the crystal to change. The LP Record Player needle is the reverse of this, the bumps on the spiral groove of the record applies pressure to needle which generates electricity. Both are piezo-electric effects.

Saturday, May 10, 2014

Fixed frequency Variable duty cycle with 555

This circuit is based on a very old application note from exar, in this the frequency is fixed by IC1 and IC2 -P1 controls the duty cycle. you need to compute the R and C values to get what you need,  LM555 data sheet.

You have to study the circuit and do something more innovative perhaps, just copying is ok for learning but it will get you nowhere, so learn and then innovate, the eagle circuit is given below so you can learn by editing it, also design a PCB with it, and you can even make a PCB at home to learn, but it is always good to get PCBs done by a PCB vendor, but you should understand his problems, then you will design well, so make a few PCBs.

Fixed frequency Variable duty cycle with 555

Edit the circuit eagle cad file del00012.zip,

Circuits by Application

Analog Circuits

  1. Battery Level Indicator
  2. Simple Sample and Hold
  3. Sample and Hold Standby
  4. Voltmeter Attenuator
  5. Precision Current Source
  6. Opamp Supply Virtual Ground

SCR and Triac

  1. Solid State Relay
  2. Normally Closed AC SSR
  3. AC-AC-SSR
  4. DC-DC SSR
  5. 2N2646 based Pulser
  6. Drive SCR thyristor

Mains Power

  1. Flashing Neon Lamp
  2. Dimmer power control
  3. Edison Bulb Life Extend
  4. Mains Current LED
  5. Mains Voltage LED

Digital Circuits

  1. Simple Digital Counter
  2. Running Lights
  3. Frequency Divider
  4. Crystal Oscillator
  5. Simple High speed switch
  6. Differential TTL converter

Measureall DMM

  1. Ohmmeter Measure Resistance
  2. Precision Digital Attenuator
  3. Precision Amplifier

Mixed Circuits

  1. Monostable Multivibrator
  2. Digital to Analog
  3. LM311 Oscillator
  4. PLL using 4046
  5. VCO with LM331
  6. BCD Thumbwheel to Analog
  7. V to F Converter ICL8038
555 Circuits
  1. OR gate with two 555
  2. fixed frequency duty cycle
  3. Pulse width modulation
  4. Astable Multivibrator
  5. uC Reset Generator
  6. LM555 Voltage Doubler
  7. 555 Power Oscillator
Discrete Circuits
  1. Isolated dual supply
  2. Sound to light converter
  3. Water operated relay
  4. Telephone Indicator
  5. Passive volume control
  6. RS232 Opto-Isolation
  7. Voltage Level Indicator
  8. Relay Driver
  9. Constant Current LED
  10. Voltage Doubler
  11. FET Current Source
Opamp Circuits
  1. Three Opamp Differential
  2. Two Opamp Differential
  3. Buffer Opamps
  4. Differential Op-Amp
  5. Inverting Opamp
  6. Non Inverting Opamp
  7. Digital gain control
  8. Square Triangle Oscillator
  9. Dual Polarity Output Amps
  10. Ammeter Precision Rectifier
  11. Voltage / Current 4-20 mA
  12. Current Source for RTD
Power Electronics
  1. Dual Power Supply
  2. Single Power Supply
  3. Battery Backup Supply
  4. 5V 1A Supply LM2575
  5. 5V Power Supply L296
  6. Dual Power Supply
  7. Tubelight Electronic Choke
  8. Voltage Doublers Multipliers
  9. White LED Lamp on Ni-Cd

uC and uP

  1. PC RS232 with MAX232A
  2. Battery Backup SRAM
  3. watchdog uC uP systems
Instrumentation Circuits
  1. Mains monitor LM3914
  2. Simple Mains monitor
  3. single digit voltmeter
  4. High Resistance Meter
  5. Diode Thermometer
  6. Function Generator
  7. Diode Leakage Tester
  8. Analog LED Ohm Meter
  9. Millivolt Source Current Loop
Process Control
  1. AD590 - temperature
  2. Thermocouple Amplifier
  3. Linearizing Thermocouple
  4. Thermocouple Amplifier
  5. 0-1V to 4-20 mA
  6. 1-5V to 4-20 mA
  7. InfraRed - Optical Switch
  8. InfraRed Detector