Thursday, November 29, 2018

Millivolt Source with Digital Potentiometer

Variable Parameters like voltage, current can be obtained by using a Digital Potentiometer. Microcontrollers or Counters operate FET CMOS Analog Switches. The switches configure resistor networks to adjust circuit performance. It could be a Speed Control of a Motor or Brightness of a Lamp. Volume controls and Tuners also can use this.

Millivolt Source with Digital Potentiometer

Description. - In this Circuit, digital potentiometer, connect pushbutton switches to fast and slow with one end to +7.5V, when you hold the button down the analog voltage will ramp up-down, fast or slow, this will enable you to make a digitally controlled millivolt source or power supply.

Digital Potentiometer - del50003

Here is a Millivolt Source i built for Calibration in the early days. It uses only CMOS Digital and Mixed Chips from Intersil and CD40xx Series.


In this Circuit, digital potentiometer, connect pushbutton switches to fast and slow with one end to +7.5V, when you hold the button down the analog voltage will ramp up-down, fast or slow, this will enable you to make a digitally controlled millivolt source or power supply.

Millivolt Source

Later i tried a unit with 8748 part of the code in my uC section. This is with Ramp-up and Ramp-down using only two buttons. This works even now, The support below is an HRC Fuse Holder made of Phenolic or Epoxy Resin. The mV Terminations are on Top.

80C39-8749 MCS-48 Examples and code

This was supposed to have Analog in and Analog out. Some parts of the circuit may be in the 80C51 page. This has ramp-up and ramp-down settings for the Increment and Decrement buttons. This helps setting setpoint quickly. There is also debouncing for the pushbutton.

No comments:

Post a Comment

Circuits by Application

Analog Circuits

  1. Battery Level Indicator
  2. Simple Sample and Hold
  3. Sample and Hold Standby
  4. Voltmeter Attenuator
  5. Precision Current Source
  6. Opamp Supply Virtual Ground

SCR and Triac

  1. Solid State Relay
  2. Normally Closed AC SSR
  3. AC-AC-SSR
  4. DC-DC SSR
  5. 2N2646 based Pulser
  6. Drive SCR thyristor

Mains Power

  1. Flashing Neon Lamp
  2. Dimmer power control
  3. Edison Bulb Life Extend
  4. Mains Current LED
  5. Mains Voltage LED

Digital Circuits

  1. Simple Digital Counter
  2. Running Lights
  3. Frequency Divider
  4. Crystal Oscillator
  5. Simple High speed switch
  6. Differential TTL converter

Measureall DMM

  1. Ohmmeter Measure Resistance
  2. Precision Digital Attenuator
  3. Precision Amplifier

Mixed Circuits

  1. Monostable Multivibrator
  2. Digital to Analog
  3. LM311 Oscillator
  4. PLL using 4046
  5. VCO with LM331
  6. BCD Thumbwheel to Analog
  7. V to F Converter ICL8038
555 Circuits
  1. OR gate with two 555
  2. fixed frequency duty cycle
  3. Pulse width modulation
  4. Astable Multivibrator
  5. uC Reset Generator
  6. LM555 Voltage Doubler
  7. 555 Power Oscillator
Discrete Circuits
  1. Isolated dual supply
  2. Sound to light converter
  3. Water operated relay
  4. Telephone Indicator
  5. Passive volume control
  6. RS232 Opto-Isolation
  7. Voltage Level Indicator
  8. Relay Driver
  9. Constant Current LED
  10. Voltage Doubler
  11. FET Current Source
Opamp Circuits
  1. Three Opamp Differential
  2. Two Opamp Differential
  3. Buffer Opamps
  4. Differential Op-Amp
  5. Inverting Opamp
  6. Non Inverting Opamp
  7. Digital gain control
  8. Square Triangle Oscillator
  9. Dual Polarity Output Amps
  10. Ammeter Precision Rectifier
  11. Voltage / Current 4-20 mA
  12. Current Source for RTD
Power Electronics
  1. Dual Power Supply
  2. Single Power Supply
  3. Battery Backup Supply
  4. 5V 1A Supply LM2575
  5. 5V Power Supply L296
  6. Dual Power Supply
  7. Tubelight Electronic Choke
  8. Voltage Doublers Multipliers
  9. White LED Lamp on Ni-Cd

uC and uP

  1. PC RS232 with MAX232A
  2. Battery Backup SRAM
  3. watchdog uC uP systems
Instrumentation Circuits
  1. Mains monitor LM3914
  2. Simple Mains monitor
  3. single digit voltmeter
  4. High Resistance Meter
  5. Diode Thermometer
  6. Function Generator
  7. Diode Leakage Tester
  8. Analog LED Ohm Meter
  9. Millivolt Source Current Loop
Process Control
  1. AD590 - temperature
  2. Thermocouple Amplifier
  3. Linearizing Thermocouple
  4. Thermocouple Amplifier
  5. 0-1V to 4-20 mA
  6. 1-5V to 4-20 mA
  7. InfraRed - Optical Switch
  8. InfraRed Detector

Search This Blog