Friday, November 14, 2014

DMM range and AC-DC mode Logic

This is the third circuit that you will need to build a Simple Benchtop DMM with no Microcontroller.

Here the U1D and U1B 4093 acts like a de-bouncing circuit for the push keys. The 4029 counts up scrolling to binary values 00, 01, 10, 11 for the four ranges.

The binary value of 4029 is decoded to decimal by 4028 in order to light four LEDs which indicates the range or mode on the front panel. When any of these pushbuttons are pressed and held, the nand schmitt 4093 clocks to scroll the range continuously. The binary output of these counters control CMOS switches 4052 which are analog multiplexers.

DMM range and AC-DC mode Logic

The DPM or DVM gives a readout of an Analog Value or process. The Analog reading we obtain from a Circuit Measurement Jig represents some real world parameter.

In a multi-parameter instrument like DMM, the measurement jig functions and the analog signal routing is done by ganged range selection switches.

Read More here DMM range and AC-DC mode Logic

Wednesday, November 12, 2014

Power supply with battery backup - DMM

This is a simple charger circuit which will work for a light load like a DMM, the Battery can be a sealed maintenance free battery of 9V-2AH or better. The circuit will work best if the Unit is powered on many times daily on regular use, else battery will drain down.

The 555 Astable is used to generate a AC signal from which a negative voltage is generated, A 79L05 which is a low power TO92 equivalent of 7905 a negative -5 volts regulator is used as -5 volts load is less. A TO220 7805 is used for the +5V supply.

Power supply with battery backup - DMM

Many dual supplies are derived from one DC Source. A SMPS solution is the best. A Series Regulator is simple to troubleshoot in comparison to Switching Types, there is no EMI-RFI too.

Power supply with battery backup - DMM

This simple circuit is ok only for Low Current gadgets, Whereas SMPS is green and efficient. In SMPS a greater care for Product Safety is required. In a Linear Supply with Step-Down Mains-Frequency Transformer. The Transformer is the only place, where you look into safety the most. In SMPS it is the PCB, the feedback components and also The High-Frequency (200 kHz) Mains Ferrite Transformer.

Tuesday, November 11, 2014

Build a DMM - LM3914 Analog display

This a part of a complete Benchtop DMM that you can build to learn the internals of a Digital MultiMeter. This is oriented towards learning the measurement aspects and the protection of input circuits.

U2A opamp LF353 is used here as a constant current source, R10-D13-D14 is for protection in case you measure voltage in the ohms range. U1 4052 helps digitally select four different currents, the currents pass thru the unknown resistor to be measured and an voltage developed across the resistor is measured.

U2B is a buffer which passes on the voltage measured to U5A for inversion of polarity as current source is a negative current (current sink). U5B amplifies to the level required for the LM3914 display circuit. U7 555 is used as a de-bouncing for switch SW1 so as to advance counter 4029 to change the range of resistance measurement.

Build a DMM - LM3914 Analog display

Use any FET input dual opamp, TLO72 will work but LM358 will cause error as it is transistor input..

D1, D12 and R8 are to ensure that the FET can be turned off, as the opamp swings from +/-3.5V only, with some FET it needs to be tweaked. LF353 is a Wide Bandwidth Dual JFET Input Operational Amplifier.

Build a DMM - LM3914 Analog display

Circuits by Application

Analog Circuits

  1. Battery Level Indicator
  2. Simple Sample and Hold
  3. Sample and Hold Standby
  4. Voltmeter Attenuator
  5. Precision Current Source
  6. Opamp Supply Virtual Ground

SCR and Triac

  1. Solid State Relay
  2. Normally Closed AC SSR
  3. AC-AC-SSR
  4. DC-DC SSR
  5. 2N2646 based Pulser
  6. Drive SCR thyristor

Mains Power

  1. Flashing Neon Lamp
  2. Dimmer power control
  3. Edison Bulb Life Extend
  4. Mains Current LED
  5. Mains Voltage LED

Digital Circuits

  1. Simple Digital Counter
  2. Running Lights
  3. Frequency Divider
  4. Crystal Oscillator
  5. Simple High speed switch
  6. Differential TTL converter

Measureall DMM

  1. Ohmmeter Measure Resistance
  2. Precision Digital Attenuator
  3. Precision Amplifier

Mixed Circuits

  1. Monostable Multivibrator
  2. Digital to Analog
  3. LM311 Oscillator
  4. PLL using 4046
  5. VCO with LM331
  6. BCD Thumbwheel to Analog
  7. V to F Converter ICL8038
555 Circuits
  1. OR gate with two 555
  2. fixed frequency duty cycle
  3. Pulse width modulation
  4. Astable Multivibrator
  5. uC Reset Generator
  6. LM555 Voltage Doubler
  7. 555 Power Oscillator
Discrete Circuits
  1. Isolated dual supply
  2. Sound to light converter
  3. Water operated relay
  4. Telephone Indicator
  5. Passive volume control
  6. RS232 Opto-Isolation
  7. Voltage Level Indicator
  8. Relay Driver
  9. Constant Current LED
  10. Voltage Doubler
  11. FET Current Source
Opamp Circuits
  1. Three Opamp Differential
  2. Two Opamp Differential
  3. Buffer Opamps
  4. Differential Op-Amp
  5. Inverting Opamp
  6. Non Inverting Opamp
  7. Digital gain control
  8. Square Triangle Oscillator
  9. Dual Polarity Output Amps
  10. Ammeter Precision Rectifier
  11. Voltage / Current 4-20 mA
  12. Current Source for RTD
Power Electronics
  1. Dual Power Supply
  2. Single Power Supply
  3. Battery Backup Supply
  4. 5V 1A Supply LM2575
  5. 5V Power Supply L296
  6. Dual Power Supply
  7. Tubelight Electronic Choke
  8. Voltage Doublers Multipliers
  9. White LED Lamp on Ni-Cd

uC and uP

  1. PC RS232 with MAX232A
  2. Battery Backup SRAM
  3. watchdog uC uP systems
Instrumentation Circuits
  1. Mains monitor LM3914
  2. Simple Mains monitor
  3. single digit voltmeter
  4. High Resistance Meter
  5. Diode Thermometer
  6. Function Generator
  7. Diode Leakage Tester
  8. Analog LED Ohm Meter
  9. Millivolt Source Current Loop
Process Control
  1. AD590 - temperature
  2. Thermocouple Amplifier
  3. Linearizing Thermocouple
  4. Thermocouple Amplifier
  5. 0-1V to 4-20 mA
  6. 1-5V to 4-20 mA
  7. InfraRed - Optical Switch
  8. InfraRed Detector

Search This Blog