Wednesday, November 07, 2012

Analog mV Switch for Digital Meters

Let us assume you have to Measure Amps and Volts in four independent circuits. This becomes a Multi Channel Voltmeter and Ammeter.

Analog-Multiplexer
This circuit uses a 4052 as a DC  Analog Multiplexer, the inputs to this Mux must be from Low Impedance Output OpAmps. The Resistors Shown are not needed once the Signal Conditioning Opamps are connected. The Restors can be 100K to keep the inputs from floating, that will not load an opamp. The resistors can attenuate signals if  sensors are directly connected.

The signals from sensors have to be amplified and corrected or scaled before reaching this Switched DVM. For Current a Shunt is the Sensor and for AC current a CT or current transformer is the sensor. Voltmeter has Attenuator as the 'Sensor'.

The 7107 DPM can be replaced by the Analog Inputs of the Arduino or Microcontrooler A/D Stage.

Wednesday, August 29, 2012

+5 to -5 using a 555 Astable Multivibrator

This is a very simple -5V supply using one 555, useful for analog blocks using FET Opamps using low power. This circuit came up when i had to design limited by inventory. It worked well for its need. It converts Positive Five Volts to Negative Five Volts to create a dual supply.

+5 to -5 using a 555 Astable Multivibrator

This +5 to -5 using a 555 Astable Multivibrator.is not a high efficiency design, in fact it cannot take a heavy load. Circuits having some CMOS Opamps and a A/D convertor is ok. Even very small battery designs must avoid this circuit.

This suits well when you want to power an analog amp which has to measure voltages which swing on either sides of zero. It can be used in a LCD based portable measuring instrument running on a rechargeable 9V battery.

Powering a strain gauge amp may be one use, another may be like a RTD temperature meter for -50 to +150 deg C.

Saturday, August 18, 2012

Analog Mux for Data Acquisition Systems

Here is a 4-20 mA In/Out Analog Mux with Cascade option. This is a simple circuit i designed to make a Automation System within a budget.\

Mixed Circuits Analog with Digital

Analog Mux using 4051

This takes 4-20mA from many Transmitters and gives out just one 4-20 mA output. The Mux is done with a digital byte or word. This is a slow scanner as process is slow, that way many analog inputs can be multiplexed and sent into one analog input of a D/A. In near real time systems a faster mux could be used or mux totally avoided. This was made in some numbers, so the pcb is better than others.

4-20mA Multiplexer Circuit - pdf

Thursday, August 16, 2012

Amp Hour Meter using LM331 and 74C926

LM331 is a Voltage-to-Frequency Converters and  74C926 is a 4 Digit Counter. The first part of the circuit converts the amplified DC analog value from a shunt to pulses. The Second counts the pulses and Displays it on a Seven segment LED display.


Amp Hour Meter using LM331 and 74C926

Circuits by Application

Analog Circuits

  1. Battery Level Indicator
  2. Simple Sample and Hold
  3. Sample and Hold Standby
  4. Voltmeter Attenuator
  5. Precision Current Source
  6. Opamp Supply Virtual Ground

SCR and Triac

  1. Solid State Relay
  2. Normally Closed AC SSR
  3. AC-AC-SSR
  4. DC-DC SSR
  5. 2N2646 based Pulser
  6. Drive SCR thyristor

Mains Power

  1. Flashing Neon Lamp
  2. Dimmer power control
  3. Edison Bulb Life Extend
  4. Mains Current LED
  5. Mains Voltage LED

Digital Circuits

  1. Simple Digital Counter
  2. Running Lights
  3. Frequency Divider
  4. Crystal Oscillator
  5. Simple High speed switch
  6. Differential TTL converter

Measureall DMM

  1. Ohmmeter Measure Resistance
  2. Precision Digital Attenuator
  3. Precision Amplifier

Mixed Circuits

  1. Monostable Multivibrator
  2. Digital to Analog
  3. LM311 Oscillator
  4. PLL using 4046
  5. VCO with LM331
  6. BCD Thumbwheel to Analog
  7. V to F Converter ICL8038
555 Circuits
  1. OR gate with two 555
  2. fixed frequency duty cycle
  3. Pulse width modulation
  4. Astable Multivibrator
  5. uC Reset Generator
  6. LM555 Voltage Doubler
  7. 555 Power Oscillator
Discrete Circuits
  1. Isolated dual supply
  2. Sound to light converter
  3. Water operated relay
  4. Telephone Indicator
  5. Passive volume control
  6. RS232 Opto-Isolation
  7. Voltage Level Indicator
  8. Relay Driver
  9. Constant Current LED
  10. Voltage Doubler
  11. FET Current Source
Opamp Circuits
  1. Three Opamp Differential
  2. Two Opamp Differential
  3. Buffer Opamps
  4. Differential Op-Amp
  5. Inverting Opamp
  6. Non Inverting Opamp
  7. Digital gain control
  8. Square Triangle Oscillator
  9. Dual Polarity Output Amps
  10. Ammeter Precision Rectifier
  11. Voltage / Current 4-20 mA
  12. Current Source for RTD
Power Electronics
  1. Dual Power Supply
  2. Single Power Supply
  3. Battery Backup Supply
  4. 5V 1A Supply LM2575
  5. 5V Power Supply L296
  6. Dual Power Supply
  7. Tubelight Electronic Choke
  8. Voltage Doublers Multipliers
  9. White LED Lamp on Ni-Cd

uC and uP

  1. PC RS232 with MAX232A
  2. Battery Backup SRAM
  3. watchdog uC uP systems
Instrumentation Circuits
  1. Mains monitor LM3914
  2. Simple Mains monitor
  3. single digit voltmeter
  4. High Resistance Meter
  5. Diode Thermometer
  6. Function Generator
  7. Diode Leakage Tester
  8. Analog LED Ohm Meter
  9. Millivolt Source Current Loop
Process Control
  1. AD590 - temperature
  2. Thermocouple Amplifier
  3. Linearizing Thermocouple
  4. Thermocouple Amplifier
  5. 0-1V to 4-20 mA
  6. 1-5V to 4-20 mA
  7. InfraRed - Optical Switch
  8. InfraRed Detector